[OpenTRV-dev] opentrv to emoncms

[Bo Herrmannsen]

hmm

my idea so far...:

i have one spare usb port left... use that with and ftdi and extend the
serial plug so i could wall mount an OpenTRV and use that one to collect
the data from all the others.

could the perl example be used to forward the data so they show up in
emoncms as individual nodes? or how does it work?

2015-05-07 16:07 GMT+02:00 Aideen McConville <aideen at amcc.myzen.co.uk>:

> Hi Bo,
>
>
>
> I too am interested in collecting data from OpenTRV, OpenEnergyMonitor
> (oem) and other sensors and wrangling it as required (e.g. sending to
> emonCMS and other possible stores/dashboards).
>
>
>
> Rather than modify (and complexify!) the code in individual sensor nodes,
> I am planning to use a central node to receive, store and forward data
> (e.g. using MQTT and Node-Red). It's fairly easy to send data from any
> sensor to emonCMS using oem's input API and the same techniques can be
> useful for the oem sensors themselves (emonTx and emonTH). I can provide a
> simple Perl example on request (sends Currentcost energy meter serial data
> to emonCMS).
>
>
>
> One OpenTRV unit could act as an interim (RFMxx) gateway - listening for
> data from other "busier" units and forwarding it to the main gateway (e.g.
> via a FTDI - USB link to a mini wireless router or Raspberry Pi).
>
>
>
> I currently have one OpenTRV Rev2 board (r4111) talking to a Conrad valve
> drive. It is connected to, and powered by, the USB port of a micro TP-Link
> router via FTDI (same USB BUB as used to talk to Jeenodes and oem units).
> The TP-Link router is running OpenWRT (embedded Linux) and has some USB
> tools and the Mosquitto client software installed (further details on
> request). A Raspberry Pi would work just as well.
>
>
>
> To "see" the serial data from the OpenTRV board, I just need to logon to
> the router and type:
>
>
>
> # stty -F /dev/ttyUSB0 4800 raw -echo
>
>
>
> # cat < /dev/ttyUSB0
>
>
>
> A further step: to remove the ">" lines from the output and pass the rest
> on to a Mosquitto broker (running elsewhere on the network):
>
>
>
> # awk 'NF > 1' /dev/ttyUSB0 | mosquitto_pub -l -h 192.168.1.112 -t
> 'house/opentrv/lab'
>
>
>
> I can then see the data on a beefier linux box (one with a hard drive!)
> running the broker:
>
>
>
> $ mosquitto_sub -t 'house/#'
>
> :
>
> FHT8V TX
>
> =F0%@20C4;T6 1 W255 0 F255 0 W255 0 F255 0;S12 12 21;HC18
> 11;{"@":"120b","L":235,"B|mV":3332,"occ|%":0,"vC|%":0}
>
> FHT8V TX
>
> FHT8V TX
>
> =F0%@20C5;T6 5 W255 0 F255 0 W255 0 F255 0;S12 12 21;HC18
> 11;{"@":"120b","L":234,"B|mV":3332,"occ|%":0,"vC|%":0}
>
> FHT8V TX
>
> =F0%@20C5;T6 9 W255 0 F255 0 W255 0 F255 0;S12 12 21;HC18
> 11;{"@":"120b","L":234,"B|mV":3332,"occ|%":0,"vC|%":0}
>
> FHT8V TX
>
> FHT8V TX
>
> :
>
>
>
> Not sure if this helps with your quest, but if any particlar details are
> of interest, let me know.
>
>
>
> Aideen
>
>
>
> *From:* opentrv-dev-bounces at lists.opentrv.org.uk [mailto:
> opentrv-dev-bounces at lists.opentrv.org.uk] *On Behalf Of *Bo Herrmannsen
> *Sent:* 05 May 2015 12:11
> *To:* Closed list for developer discussions
> *Subject:* [OpenTRV-dev] opentrv to emoncms
>
>
>
> hi again
>
>
>
> i'm going to fiddle with my bed-roller server box and i wanted to add data
> from the OpenTRV units
>
>
>
>
>
> 2 ways i can think of it
>
>
>
>
>
> 1) Each Opentrv board sends the data to emoncms... they at least work on
> the same freq, but they dont use the same module,... latest rfm lib that
> emontx boards use are updated to be able to use rfm69 but i think their
> boards are still shipped with rfm12 or was it  22....
>
>
>
> anyways my idea was to send commands to the valve, then to emoncms... then
> sleep for the 2 mins or so
>
>
>
>
>
> 2) have one emontx board grap the data it needs from one Opentrv board
> that again wireless gets data from the others.... i have 2 emontx boards
> and one opentrv at my hot water cylinder...
>
>
>
> one of the emontx boards allready gets data from the heatmeter via an IR
> optical serial port
>
>
>
> the other one only monitors my water meter so most of the time it will
> just sit there idle and just report 0 water usage to the emoncms system...
> i think this one will be mostly suited
>
>
>
> right now that board only sends over 2 numbers
>
>
>
> 1) liters an hour
>
> 2) clicks since last reading (liters)
>
>
>
> it reports to emoncms every 4 sec
>
>
>
> so for each opentrv i just need to collect and add:
>
>
>
> 1)battery voltage
>
> 2)temp
>
> 3)light level
>
> 4)valve open %
>
>
>
> i have attached 2 files... one for each of the emontx boards
>
>
>
> the small file is the one for the water meter and the other is for the
> heatmeater, electricity pulse, and hotwater temp...
>
>
>
> my idea is to add something to the watermeter skecth that can grab serial
> data and pick what is needed... i just dont have any clue how.. also the
> serial data from the opentrv must be in the same order or the emontx will
> start to report false data.... maybe have the opentrv buffer the data and
> just update the output when new values are there?
>
>
>
> anyone have idea or could help out?
>
>
>
> the zip file is the sketch for my opentrv that controls the hot water
>
>
>
> _______________________________________________
> OpenTRV-dev mailing list
> OpenTRV-dev at lists.opentrv.org.uk
> http://lists.opentrv.org.uk/listinfo/opentrv-dev
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.opentrv.org.uk/pipermail/opentrv-dev/attachments/20150507/f5b49574/attachment.html>